Mpp Electric Power Pipe Small Diameter Sizes Mpp Conduit Plastic Pipe

• Customization: Available
• After-sales Service: Online After-Sales Service
• Warranty: 1 Year
• Model NO.: DN100mm-250mm
• Material: PP
• Water Absorption: ＜0.01%
• Contraction Percentage: ＜0.4%
• Ring Stiffness: Sn24, Sn32, Sn40
• Density: 0.90-0.94
• Flattening Test: When The Deformation in The Vertical Direction of
• Bending Strength: ≥36 MPa
• Colour: to Be Agreed Upon by Supply and Demand
• Link Mode: It Is Connected by Hot Melt Butt
• Transport Package: Customized According to Customer Requirements
• Specification: According to the customer can be customized
• Trademark: Wilvida
• Origin: Jiangsu, China
• HS Code: 3917210000
• Production Capacity: 100, 000t/Year

Product Description

Product Description

 

MPP power pipe adopts modified polypropylene as the main raw material. It does not need to dredge, dig up and destroy the road surface, and lay pipelines, cables and other construction projects in special sections such as roads, railways, buildings and river beds.

Compared with the traditional "digging method, trenchless pipe engineering more adapted to the requirements of environmental protection, because the traditional construction caused by the removal of dust, traffic congestion and other disturbing factors, this technology can also be unable to carry out excavation work in laying pipelines, such as Heritage Conservation District, downtown, and crops farmland protection areas, highways, rivers etc.

It has much advantages of high strength,good high temperature resistant performance,easy installing,convenient construction,low cost and so on.
 

Detailed Photos

Product Parameters

MPP Cable Conduit Pipe's Parameter Datas
Norminal Diameter/IN(mm)	Norminal Wall Thickness (mm)			Norminal Lenght (mm)
	Ring Stiffness (3%) Grade (Normal Temperature)
	SN24	SN32	SN40
100	8	8	10	6000/9000
125	8	10	12
150	10	12	14
175	12	14	16
200	14	16	18
225	16	18	20
250	18	20	20

Certifications

Packaging & Shipping

Installation Instructions

In the installation process of MPP power cable protection tube, the connection method is a very important part. The correct selection of the appropriate connection method can ensure the reliable operation of the power piping system. This section introduces several common MPP power cable protection tube connection methods to help you understand the characteristics and application scenarios of each method.

01,Before installation, check whether the power supply, hydraulic oil, and heating plate of the welding machine meet the welding requirements; Conduct an empty car test run on the milling cutter oil pump switch, etc; Install the slips that match the specifications of the pipe into the rack; Set the temperature of the heating plate to the welding temperature, and before heating, wipe the surface of the heating plate with clean soft paper or alcohol to clean its oil stains.

02,Remove dirt from both ends of the pipe. Place the pipe into the frame clamp so that the length of the extension at both ends is equal. The parts outside the pipe rack should be supported by supports. Place the pipe at the same height as the centerline of the frame, and then secure the slip. Insert a milling cutter and mill the pipe.

03,After milling the pipe until continuous cutting occurs at both ends of the pipe, remove the pressure and let the milling cutter idle for two or three weeks before retracting the movable frame and turning off the milling cutter switch.

04,Take out the milling cutter and close the pipes at both ends. Check the end face, and the displacement of both ends of the pipe should not exceed 10% of the pipe wall thickness. When closing, there should be no obvious gap between the two end faces of the pipe, and the gap width should comply with: 0.3MM (DN<25MM); If 0.5MM (225MM400MM) does not meet the requirements, it should be milled again.

05,When the temperature of the heating plate reaches the set value, quickly place it into the rack and apply the specified pressure until the circumference of the pipe ends is flipped and the minimum curling reaches the specified height. Reduce the pressure to the specified value, so that the end face of the pipe is in contact with the heating plate, and continue heating until the specified time.

06,When the heat absorption time reaches the specified value, retract the movable frame and quickly remove the heating plate. Close the two pipe ends, and the switching time should be as short as possible, not exceeding the specified value. The closing pressure should not be too high, otherwise it will squeeze out the molten material and cause a decrease in welding quality.

07,Raise the pressure to the specified value and maintain pressure for cooling. After natural cooling to room temperature, release the pressure, loosen the slip, remove the pipe, and complete the welding.
 

Company Profile

Yangzhou Huawei Pipe Technology Co., Ltd. was established in Yangzhou, China in 2018, dedicated to providing one-stop intelligent pipeline system solutions.
Our company's main products include HDPE, PVC, PP-R, MPP and other series, which are widely used in construction engineering, municipal engineering, agricultural drainage and irrigation, gas transportation, home decoration, power cable sheathing and other fields. There are nearly 3000 different varieties and specifications of pipes, fittings, and valve products.

Our Adrantages
We devote ourselves continuously to international trade and supply pipeline dealers who come from all over the world with customized services. In order to build a modern factory, we invest in a series of professional mechanical equipment.  The annual output amounts to 30000 tons, which can fill up 3000 containers.
The excellent machinery and consummate management system can reduce cost, shorten delivery time and ensure the quality of every product.

FAQ

Are you trading company or factory?

We are a professional manufacturer and welcome to visit our factory at your time.

How long is your delivery time? For small quantity products, they will delivered to you by international courier(DHL, FedEx, TNT etc.) or by air. Usually it will cost 3-5days that you can get the goods after delivered. For large quantity products,delivered by sea.It will cost days to weeks to come to your destination port, which depends on where is the port.

Can you provide samples?

Yes, Samples are available. For normal products, samples are free ,you just need to bear the freight; For those high value products, you need to pay the freight and certain product cost. After we cooperate for some times or when you are our VIP customer, free sample will be offered when you need.

Do you supply OEM service?

Yes, we offer OEM service according to your request,such as LOGO,package etc.

What is your terms of payment?

TT or L/C at sight, T/T 30% in advanced, balance before shipment or by L/C.

What is your MOQ?

As customers' requests

Is there any possible to use my appointed label or package?

Yes. If needed, we'd like to use label or package according to your requirement.

How can you guarantee the goods you offer is qualified?

We always believe that honesty and responsibility are basis of one company, so all products that we provide for you all qualified. We will have goods tested and provide COA before deliv- ery for sure.